Full Moon Distortion

fmd.png

  1. Bypass Footswitch
  2. Jewel Indicator
  3. Output Jack
  4. Level
  5. Hi-Treble
  6. Treble
  7. Boost
  8. Boost LED
  9. Middle
  10. Bass
  11. Gain
  12. Bite Switch
  13. Texture Switch
  14. Input Jack
  15. Boost Footswitch
  16. Low Battery Indicator
  17. LED Kill Switch
  18. DC Power Connector

Fender Full Moon Distortion

Thanks for purchasing the Full Moon Distortion — a high gain distortion pedal with flexible tone shaping capabilities. Engineered to deliver heavy distortion without losing clarity, the Full Moon is equipped with a four-band EQ to help match this pedal to any guitar/amp combination. The Texture and Bite Switches offer additional tools to tweak your sound. The Full Moon also offers a boost that can increase the overall volume.
Between the EQ section, toggles, and boost, this distortion pedal is capable of adding snarl to chugging rhythms or creating soaring single-note leads.

DESIGNED IN CALIFORNIA, U.S.A.

Level

This control adjusts overall volume level.

Hi-Treble

A useful control for smoothing out high gain. It softens the upper frequencies and works to blend in the right amount of sizzle.

Treble

This controls the pedal’s high-frequency response. Dial it in to keep the top end of your notes clear and defined.

Middle

This controls the pedal’s midrange response. A versatile control useful in all distortion settings.

Bass

This controls the pedal’s low-frequency response. Use this to fatten up thinner-sounding guitars, or roll it back to clear up guitars with too much bottom end.

Boost

This control adjusts the amount of volume added when the Boost is engaged.

Boost LED

This LED shows when the Boost is engaged.

Gain

This control adjusts the amount of distortion or saturation.

Texture Switch

This toggles between asymmetrical and symmetrical clipping.

Bite Switch

This switch adds extra gain at upper frequencies, reducing potentially boomy low end and lets your instrument cut through the mix.

Jewel Indicator

The Jewel Indicator shows when the distortion effect is active

Bypass Footswitch
This rugged footswitch bypasses the effect.

Boost Footswitch

This switch provides extra output level set by the Boost control.

Input Jack

This is a high-impedance input suitable for electric guitar, bass, keyboards and other instruments.

Output Jack

This is a low-impedance output jack that connects to the amp or to the next effect pedal in the signal chain.

DC Power Connector

This is a standard center-negative 9VDC jack for use with appropriate power supplies.

LED Kill Switch

This switch extinguishes the LEDs that illuminate the control knobs—useful in maximizing battery life when running the pedal from batteries.

Low Battery Indicator

This red LED on the front of the battery door illuminates when battery voltage drops below a set threshold, indicating that the battery should be replaced soon.


A PRODUCT OF:
FENDER MUSICAL INSTRUMENTS CORPORATION
CORONA, CALIFORNIA, USA
Fender® is a registered trademark of FMIC.
Copyright © 2018 FMIC. All rights reserved.
P/N 7714183000 – REV A

Important Safety Instructions

  • WARNING: To prevent damage, fire or shock hazard, do not expose the unit or its AC power to rain or moisture.
  • Do not alter the AC plug of the connected power adapter
  • Do not drip or splash liquids on the unit.
  • No user serviceable parts inside, refer servicing to qualified personnel only.
  • WARNING: The unit must only be connected to a safety agency certified, regulated, power source (adapter), approved for useand compliant with applicable local and national regulatory safety requirements.
  • Unplug the AC power adapter before cleaning the unit exterior. Use only a damp cloth for cleaning and then wait until the unit is completely dry before reconnecting it to power.
  • Amplifiers and loudspeaker systems, and ear/headphones (if equipped) are capable of producing very high sound pressure levels which may cause temporary or permanent hearing damage. Use care when setting and adjusting volume levels during use.

Languages

Manual available in Espanol, francais, Italiano, Deutch, Portugues, (Chinese)
www.fender.com/support
Expanded Owner’s Manual
Expanded Owner’s Manual available at:
www.fender.com/support

Specifications

IMPEDANCES:INPUT: 1MΩ OUTPUT LOAD: >10kΩ
POWER SUPPLY:One 9V battery or 9VDC regulated adapter,
5.5 x 2.1 mm barrel connector, center negative
POWER REQUIREMENTS:80mA @ 9VDC
10mA, Total Current Consumption
DIMENSIONS:3.75” x 4.9” x 2.5” (95.25mm x 124.5mm x 63.5mm)
WEIGHT:1.2lbs (.54kg

Product specifications subject to change without notice

Note: This User's Manual is adapted from the official manual created by Fender in PDF format, without modification of the content. We just rewrite the PDF, into responsive mobile friendly pages.So, you can read this document anytime and anywhere.

Similar Manuals

you're currently offline