the-trapper.png

  1. Bypass Footswitch
  2. Jewel Indicator
  3. Output Jack
  4. Contour
  5. Tone
  6. Level 1
  7. Level 1 LED
  8. Level 2
  9. Fuzz 2
  10. Octave Switch
  11. Input Jack
  12. Select Footswitch
  13. Low Battery Indicator
  14. LED Kill Switch
  15. DC Power Connector

Thanks for purchasing The Trapper – a radical new dual fuzz pedal. The Trapper features two distinctly different voices that can be toggled used the Select Footswitch. The first voice features dedicated Fuzz and Level controls, as well as a high-octave toggle switch. The second fuzz relies mainly on the guitar’s volume and tone controls for modification, with Level as the only parameter.
This circuit also employs a noise gate for some truly distinctive “glitchy” sounds.

DESIGNED IN CALIFORNIA, U.S.A.

Contour

Controls frequency range emphasis. Turn knob counterclockwise for bass boost/treble cut; turn clockwise for opposite. At middle position, mid frequencies are de-emphasized.

Tone

Controls amount of high-frequency signal content. Turn counterclockwise for darker sound; turn clockwise to brighten sound.

Level 1

Controls output level of first fuzz circuit.

Level 1 LED

Illuminates when first fuzz circuit is selected.

Level 2

Controls output level of second fuzz circuit.

Fuzz 2

Controls amount of fuzz in second circuit; turn clockwise for greater saturation.

Octave Switch

Adds a high octave to signal.

Jewel Indicator

Illuminates when effect is engaged.

Bypass Footswitch

Bypasses effect.

Select Footswitch

Toggles between both fuzz circuits.

Input Jack

High-impedance input suitable for electric guitar, bass, acoustic guitars with pickup systems, keyboards and other instruments.

Output Jack

Low-impedance output jack connects to amp or to next effect pedal in signal chain.

DC Power Connector

Standard center-negative 9VDC jack for use with appropriate power supplies.

LED Kill Switch

Deactivates control-knob illumination


A PRODUCT OF:
FENDER MUSICAL INSTRUMENTS CORPORATION
CORONA, CALIFORNIA, USA
Fender® is a registered trademark of FMIC.
Copyright © 2019 FMIC. All rights reserved.
P/N 7717102000 – REV 1

Important Safety Instructions

  • WARNING: To prevent damage, fire or shock hazard, do not expose the unit or its AC power to rain or moisture.
  • Do not alter the AC plug of the connected power adapter
  • Do not drip or splash liquids on the unit.
  • No user serviceable parts inside, refer servicing to qualified personnel only.
  • WARNING: The unit must only be connected to a safety agency certified, regulated, power source (adapter), approved for useand compliant with applicable local and national regulatory safety requirements.
  • Unplug the AC power adapter before cleaning the unit exterior. Use only a damp cloth for cleaning and then wait until the unit is completely dry before reconnecting it to power.
  • Amplifiers and loudspeaker systems, and ear/headphones (if equipped) are capable of producing very high sound pressure levels which may cause temporary or permanent hearing damage. Use care when setting and adjusting volume levels during use.

Additional Languages

Manual available in additional languages at:
www.fender.com/support

Specifications

IMPEDANCES:INPUT: 820kΩ OUTPUT: 470Ω
POWER SUPPLY:One 9V battery or 9VDC regulated adapter,
5.5 x 2.1 mm barrel connector, center negative
POWER REQUIREMENTS:290mA @ 9VDC
DIMENSIONS:3.75” x 4.9” x 2.5” (95.25mm x 124.5mm x 63.5mm)
WEIGHT:1.2lbs (.54kg

Product specifications subject to change without notice

Note: This User's Manual is adapted from the official manual created by Fender in PDF format, without modification of the content. We just rewrite the PDF, into responsive mobile friendly pages.So, you can read this document anytime and anywhere.

Similar Manuals

you're currently offline